SLIM薄机4G 9.6A进入XELL的破解教程翻译
作者:阳光电玩小亮(原帖点击进入)
小亮首先申明!本人英文水平有限 不保证翻译的完全正确性。破解有风险,请谨慎!本人不为以下翻译造成的任何后果负责 以下翻译只为同好共同研究!小亮欢迎共同探讨 旺旺id cashimi001 qq51073616 小亮稍后会放出16M芯片的换方法。
怎么破解corona v2 (也就是4G版的9.6A机器)进入XELL并得到你的CPUKEY 感谢GLITCH360TEAM
需要准得工具:
1.1个能读取SD卡的读卡器、和线
2.26-28平方毫米的导线 (不要使用聚偏二氟乙烯涂料的线材)
3.1个 68欧姆的电阻(也可以用60欧或者80欧替代)
4.一台XBOX360 CORONA V2主板的主机 (废话)
5.winhex软件
6.Xebuild 2.0.82合成软件
第一步:焊接读卡器到XBOX360上的U1D1输出

u1d1.1连接68欧姆电阻到VDD SD卡的第四脚
U1D1.2连接到CLK SD卡的第5脚
U1D1.3连接到CMD SD卡的第2脚
U1D1.4连接到接地 SD卡上的第3或者第6脚
U1D1.11连接到DATA3 SD卡上的第1脚
U1D1.13连接到DATA1 SD卡上的第8脚
U1D1.14连接到data2 sd卡上的9脚
Wires are to connect on a mmc/sd card reader not on a sd card itself.
Use AWG26 or 28 for all the wiring and AWG24 for both GND. This is important
是连接到SD卡读卡器而不是SD卡 使用AWG26或 28焊接所有的用AWG24导线用来接地 这个很重要
其中AWG是美国的线材标准 附AWG的百科地址http://zh.wikipedia.org/wiki/%E7%BE%8E%E5%9B%BD%E7%BA%BF%E8%A7%84
You also need to connect pin 1 of the main xbox 360 resonator to ground (C1E1 right pin is a good point)
你同样像下图一样 用线连接PIN1 到XBOX360主板的电阻周围像图片上的一样(C1E1是比较好的点)

Make sure the data write lock in disabled on your MMC/SD card Reader.
确认你SD卡读卡器的防写入开关为 disabeld状态 也就是关闭状态
Step 2: Get your 16MB nand dump file
Once you got this all wired up to your card reader, plug the card reader to your usb after that plug the power on your
xbox 360.
You should get a popup saying a drive (remember the drive letter) is unformatted, do you want to format it, of course
say NO!
Load WinHex, go to Tools > Open Disk….
第2步:得到你的16M NAND文件
焊接好你的读卡器之后,把读卡器插在电脑上的USB口上,然后打开你XBOX360的电源
这时候应该会找到一个新即插即用设备,(记得安装驱动)连接好之后显示的是未格式化,难道你想要去格式化它?千万不要!!!
打开WINHEX软件 打开TOOLS 下的OPEN DISK

Under Logical Media you should see: Removable Medium (your drive letter), Removable Medium « x »
在弹出窗口 你应该可以看到 :可以移动媒体 (你的读卡器识别出来的识别号这里用X)可移动媒体 X

Now search under physical media for the drive and load it
Now you can now see the contents of the 4GB nand
At this point we will extract the 16MB nand from the 4GB nand
Select the first value of the first offset (0), right click and select beginning of block
现在找到 找到读卡器设备读取它 现在你可以看到4GB NAND 现在我们可以在4GNAND里提取出16MB的NAND文件
选择第一个值用鼠标右键(如下图)选 begining of block

Then use Alt+G and go to offset 107FFFF
然后按ALT+G输入 107FFFF

评论